No results were found for the filter!
Aluminum foil, self-adhesive, 100mm width
Aluminum foil, self-adhesive, perfect for shielding of DIY projekts, easy to use. 100mm width. Price is per meter Picture shows processing
Remember
Part Number: Z-KBA
Aluminum plate black anodized, 42x35mm, 2mm thick
Aluminum plate black anodized, 42x35mm, 2mm thick. In conjunction with our SW1020 (see recomendation below) the perfect item to install a reliable impedance selector switch in older Marshall's (Plexis and JMP´s up to ´79, hole spacing...
Remember
Part Number: BM-SW1-BLECH
Eyelet for DIY projects or modifications of Fender style fiberboards
Wide Roll Eyelet for DIY projects or modifications of Fender style fiberboards. mounting diameter 1/8" / 3,2mm heigth 0.156"/ 4mm outer diameter 2"/ 5mm material: brass, tin plate
Remember
Part Number: Z-EYELET
Eyelet tool kit
Eyelet tool kit for mounting eyelets into fiberboards
Remember
Part Number: Z-EYELET-TL
EYELETBOARD - TAD KIT: Stand Alone Reverb Unit 6G15
made in the traditional way as used by Fender since the 50s till the 70s. Including isolation board without eyelets and holes like pictured. For the TAD KIT: Stand Alone Reverb Unit 6G15 with additional eyelets for proper grounding...
Remember
Part Number: K-FB6G15-A
Eyeletboard for Bias rectifier (Super Reverb, Pro Reverb)
Eyeletboard for the Bias supply in Amps with tube rectifier like used in: Super Reverb Pro Reverb Deluxe Reverb Princeton Reverb etc.
Remember
Part Number: K-FBTR
Eyeletboard for speaker wiring of Super Reverbs et
Speaker (aka ''Spider'' or ''Junction'') Fiberboard, Used on Tweed Bassmans, Blackface Twins, Blackface Super, etc
Remember
Part Number: K-FBSPKR
EYELETBOARD Tweed Super 5F4 / Pro 5E5A Style / Bandmaster 5E7
made in the traditional way as used by Fender since the 50s till the 70s. Set consisting of eyeletboard and isolation board
Remember
Part Number: K-FB5F4.5E5.5E7
Eyeletboard typical use for Solid State rectifier
Eyeletboard typical use for Solid State Rectifier like used in Twin Reverb, Showman, Bassman 100, Bandmaster etc (AB763)
Remember
Part Number: K-FBSSR
Eyeletboard typical use for: Small Cap board (AB763 blackface amps)
Eyelet board for the electrolytic capacitors in the power supply of the Fender Amps with the AB763 circuit. These are the blackfaced Fender Deluxe Reverb, Super Reverb, Pro Reverb, Vibrolux Reverb etc. Fits also many Silverface models...
Remember
Part Number: K-FBSC
Eyeletboard use for Blackface Princeton Reverb AA1164 circuit
eyelet board according style AA1164 circuit with separate insulation board
Remember
Part Number: K-FBPR
Eyeletboard without eyelets
Eyeletboard without eyelets made in the traditional way as used by Fender since the 50s till the 70s. includes: 1 board without mounted eylets + 1 insulation board without eyelets dimensions: 368 x 62 mm
Remember
Part Number: K-FB001
Eyeletboard: Brownface Deluxe 6G3 Style
made in the traditional way as used by Fender since the 50s till the 70s. 6,2cm x 26,3 cm
Remember
Part Number: K-FBBRDLX
Eyeletboard: Blackface Amps with Reverb type AB763
Eyeletboard: Blackface Amps with Reverb type AB763 AB763 type boards have been used for several models including Super Reverb, Deluxe Reverb, Twin Reverb, Pro Reverb, Vibrolux Reverb made in the traditional way as used by Fender since...
Remember
Part Number: K-FBAB763R
Eyeletboard: Blackface Vibrochamp AA764
made in the traditional way as used by Fender since the 60s till the 70s.
Remember
Part Number: K-FBCVC
Eyeletboard: Tweed Bassman 5F6 Style
made in the traditional way as used by Fender since the 50s till the 70s.
Remember
Part Number: K-FBBM
Eyeletboard: Tweed Cap Board (5F6 Bassman / 5F8 Twin Amp)
EYELETBOARD, tweed filter supply board 5F6-A Bassman, 5F8-A High Power Twin Eyelet board for the electrolytic capacitors in the power supply of the Fender Amps with the 5F6, 5F6-A, 5F8 and 5F8-A circuit. These are the TWEED Fender...
Remember
Part Number: K-FBTC
Eyeletboard: Tweed Champ Style 5F1
made in the traditional way as used by Fender since the 50s till the 70s.
Remember
Part Number: K-FBCHMP
Eyeletboard: Tweed Deluxe 5E3 Style
made in the traditional way as used by Fender since the 50s till the 70s. 7,5cm x 22cm
Remember
Part Number: K-FBDLX
Eyeletboard: Tweed Twin High-Power Style 5F8
made in the traditional way as used by Fender since the 50s till the 70s.
Remember
Part Number: K-FBTTHP
Eyeletboard: Tweed Twin Low-Power Style 5E8
made in the traditional way as used by Fender since the 50s till the 70s.
Remember
Part Number: K-FBTTLP
Eyeletboard: Tweed Vibrolux Style 5F11
Eyeletboard for the Fender Tweed Vibrolux 5F11 made in the traditional way as used by Fender since the 50s
Remember
Part Number: K-FBVLX
Hole Plug 16mm
Hole Plug 9,5-11mm, black, plastic, outside diameter 16mm Easily press into mounting holes to form a clean, extremely flat cover. Ideal for closing unnecessary holes.
Remember
Part Number: HR9025
Hole Plug 18,5mm
Hole Plug 12,7-14,3mm, black, plastic, outside diameter 18,5mm Easily press into mounting holes to form a clean, extremely flat cover. Ideal for closing unnecessary holes.
Remember
Part Number: HR9026
Top seller
Viewed