Blackface Vibroverb Style AB763 Style Amp-Kit
Amp Kit Blackface Vibroverb Reverb AB763 Style with ca. 45 watt power.
THE 15" KING !
The sweet yet shiny tone of the 6L6 tubes,
the pushing 15" speaker, the famous tube reverb, the Tremolo.
Probably one of the most sought after vintage Fender style
amps as this one does have all the features of the original vintage beast got famous for.
Power: ca. 45 Watt
Impedance: 8 Ohm
Tubes: 2x 12AT7, 4x ECC83 WA, 1x 6L6WGC-STR pair, 1x 5AR4
Reverg Can: RV-4AB3C1B
The pure kit without cabinet:
Measure: 4,5cm height x 59,5cm width x 21,5cm depth
Total weight: ca. 10 kg
Kit incl.1x15" cabinet coverd with black tolex
with silver&black grill cloth, sphinx glides and strap-handle.
Measure: 50,8cm height x 64,1cm width x 26,7cm depth
Total weight: ca. 19 kg (without speaker)
Kit,cabinet and speaker.
Nothing is missed here.
The speaker is our recommendation
and perfectly matched to the kit.
As an extra we give a discount of 10% to the speaker.
The discount is already factored in the total price
and only available for this version!
Speaker: 1x Jensen C15N 15'' 50W 8 Ohm #LJEC15N
< Measure: 50,8cm height x 64,1cm width x 26,7cm depth
Total weight: ca. 23 kg
TAD Premium Selected Tubes:
2x #RT002 12AT7, 4x RT008 ECC83 WA, 1x RT812 6L6WGC- Paar, 1x RT501 5AR4,
eyeletboards, ceramic sockets, mounting materials, full size pots, knobs, Orange Drop caps,
carbon composition resistors, cloth-covered wire, chrome chassis, transformers etc.
Front and rear panel must be ordered additionally.
*Note: the Amp-kits do not include the front and backpanel and they must therefore be ordered separately. (See matching products). If you have your kits assembled by us, the TAD generic front and back panel are included.
Footswitch and cover optional. > See matching products.
Please note that the Amp-Kit are not a beginners project but for experienced amp builders!
Voltages inside tube amplifiers can exceed 500V and can cause serious damage and can even kill!
1.) Paper in oil caps for the 6 filter caps @ 0.1uf instead the orange drop.
2.) Matched section of 220K resistor
3.) No tubes in V1
4.) 5751 in V2 (NOS Rayethon triple mica of 1963)
5.) 12Ax7 in V6 for PI (NOS RCA grey plate of the 60′s)
6.) All other tubes are NOS
7.) Weber Neomag 15” speaker, 75 watt, 8 ohm, neomydium magnet, light doped, aluminium dust cap, Weber beam blocker direct sewn on the grill, to eliminate the ice pick due to the aluminium cap. (the paper in oil cap are for this raison too)
8.) EVM 15L speaker (same as SVR!), 300 watt, 8 ohm, a monster!!! Ceramic Magnet, in a external cab to make the comparison ( i prefer the Weber, or the two speaker together, but not the EVM alone)
9.) SPS pot for disconnect the vibrato canal. With the intensity on 0, 50% of the current continue to drive the canal. With the SPS pot, 100% of the current drive the V2 = more harmonic, mor fat and hot tone. I give you here a tricks to eliminate the “pops” noise due to the residual current: you sold a 1Mohm resistor between the two lugs on the pots and that’s it, no more noise!!!
10.) KT66 tubes in place of 6L6.!!!! Check your tranny before, to be sure that he support that!!! (6L6 need 0,9 A and KT66 need 1,2 A for heater current). This tube are amazing and make for me a huge difference for approach the SRV sound : the sweet pot or crunch start with the volume at 3,5 / 4!!! The distortion is like broken glass, creamy, air, transparent, with a medium bump,like if a TS808 was in the circuit. Each note is distinctive, tight bass, clean medium and treble. Until i have put this KT66, i don’t use never my TS pedal!!! It’ amazing!!!